/* Infrared_Testpattern.ino Example sketch for IRLib2 and Circuit Playground Express
 *  Send an easily recognized pattern of bits from one Arduino
 *  to another to verify that your protocol is working. Load
 *  this sketch to send a signal. Use the "dump" sketch on the other
 *  Arduino to receive codes. Open the serial monitor and type the  
 *  number Of the protocol want to test.
 */
#include <Adafruit_CircuitPlayground.h>

#if !defined(ARDUINO_SAMD_CIRCUITPLAYGROUND_EXPRESS)
  #error "Infrared support is only for the Circuit Playground Express, it doesn't work with the Classic version"
#endif

void setup() {
  CircuitPlayground.begin(); 
  Serial.begin(9600);
  while (!Serial); // Wait for serial console
  
  Serial.println("Type the protocol number: 1-12 Or '-1' for all");
}

void sendOne(uint8_t protocol, uint32_t data, uint16_t data2 = 0, uint8_t khz = 0) {
  Serial.print("Protocol #"); Serial.print(protocol, DEC);
  Serial.print("\t"); Serial.print(Pnames(protocol));
  Serial.print("\t data = 0x"); Serial.print(data, HEX);

  if (data2) {
    Serial.print("\t data2 = 0x"); Serial.print(data2, HEX);
    Serial.print(" "); Serial.print(data2, DEC);
    Serial.print(" dec");
  }
  if (khz) {
    CircuitPlayground.irSend.send(protocol, data, data2, khz);
    Serial.print("  khz="); Serial.println(khz,DEC);
  } else {
    CircuitPlayground.irSend.send(protocol, data, data2);
    Serial.println();
  }
  delay(2000);
}
#define PATTERN1 0x12345678
#define ALL1S    0xFFFFFFFF

void doTest (uint8_t P) {
  switch (P) {  
    case 1: sendOne(1,PATTERN1);      //NEC Regular data
            sendOne(1,REPEAT_CODE);   //NEC Special ditto repeat code
            sendOne(1,PATTERN1,40);   //Pioneer is NEC with 40 kHz modulation
            break;
    case 2: sendOne(2,PATTERN1,12);   //Sony 12 bits
            sendOne(2,PATTERN1,15);   //Sony 15 bits
            sendOne(2,PATTERN1,20);   //Sony 20 bits
            break;      //Note: Sony always sends three copies of signal
    case 3: sendOne(3,ALL1S,13);      //RC5 
            sendOne(3,ALL1S,14);      //RC5-F7
            sendOne(3,ALL1S,14,57);   //RC5-F7-57
            break;
    case 4: sendOne(4,0x0ffff,20);    //RC6-0-16 Original Phillips RC6
            sendOne(4,0xcfffff,24);   //RC6-6-20 Used by some Sky and Sky+ remotes
            sendOne(4,0xcfffff,28);   //RC6-6-24 a.k.a. "Replay" protocol
            sendOne(4,ALL1S,32);      //RC6-6-32 a.k.a. "MCE" protocol
            break;
    case 5: sendOne(5,ALL1S);         //Panasonic_Old 22 bits used by some SA and Cisco cable boxes
            break;
    case 6: //JVC use "true" for first frame, "false" for repeats
            //When "true" it automatically sends one repeat. Use "false"
            //for additional repeats. The 2 lines below will actually send 
            //a total of 3 frames... A first and 2 repeats.
            sendOne(6,PATTERN1,true); 
            sendOne(6,PATTERN1,false); 
            break;      
    case 7: sendOne(7,PATTERN1);      //NECx used by many Samsung TVs
            sendOne(7,REPEAT_CODE);   //Some varieties use ditto 
            break;
    case 8: sendOne(8,0x12345,0x1234);//Samsung36 16 bit address +20 data
            break;
    case 9: sendOne(9,PATTERN1);      //G.I.Cable 16 bits with ditto repeat
            sendOne(9,REPEAT_CODE);   //This will report NEC if both protocols used
            break;
    case 10:  sendOne(10,PATTERN1);     //DirecTV default no repeat, 38 khz
              sendOne(10,PATTERN1,true);//3rd parameter is repeat flag
              sendOne(10,PATTERN1,false,40);//4th is khz, 38, 40, 57 are legal
              break;
    case 11:  sendOne(11,ALL1S,12);   //RCMM Phillips protocol used by U-Verse
              sendOne(11,ALL1S,24);   //also 24 or 32 bit possible
              sendOne(11,ALL1S,32);
              break;
    case 12:  sendOne(12,CYKM_MOUSE_MOVE+CYKM_DIR_RIGHT);//Move mouse right
              sendOne(12,CYKM_MOUSE_MOVE+CYKM_DIR_UP);   //Move mouse up
              sendOne(12,CYKM_MOUSE_MOVE+CYKM_DIR_LEFT); //Move mouse left
              sendOne(12,CYKM_MOUSE_MOVE+CYKM_DIR_DOWN); //Move mouse down
              break;    
  };
  
}
void loop() {
  if (Serial.available () > 0) {
    int16_t i = Serial.parseInt();
    if(i==-1) {
      for(i=1;i<=12;i++) {
        doTest(i);
      };
    } else {
      doTest(i);
    }
  }
}